Esi Audioterminal 010 User Manual

21. Introduction to Audioterminal 010 ...3 Features...

112. The ‘Found New Hardware Wizard’ will pop up in the following windows. Press Next. 3. Select ‘Search for a suitable driver for my device (rec

124. Specify the location of the driver. Insert the provided diskette into the floppy disk drive and select ‘floppy disk drives.’ 5. Now Windows

13 6. When you see this kind of messages, simply ignore it and just select ‘Yes’.

147. Please follow Windows instruction, step by step. Even your computer keep asking restart your computer, Keep going to install it step by step.

158. When you see this kind of messages again, simply ignore it and just select ‘No’. Even your computer keep asking restart your computer, Keep goin

16

179. After install AT010 EWDM Midi1,2 , Finally You need to Reboot your computer. 10. After rebooting, Go to ‘My computer -> Control Panel -&

184. Input/Output of the Audioterminal 010 Audioterminal 010 supports various multiple digital formats such as ADAT, TDIF, and R-BUS. These formats s

191. External Connection Cable Port This port is connecting for the exclusive external connection cable that has 1In/1Out 16 channels MIDI Interface

204. 25pin Dsub-TDIF/R-BUS Connection port In this port, you can connect TDIF and R-BUS format. You can select it on the Audioterminal 010 control p

31. Introduction to Audioterminal 010 Thank you for choosing Audioterminal 010. The Audioterminal 010 is a 100% full digital I/O Audio Interface car

215. Audioterminal 010 Control Panel If you complete the Audioterminal 010 hardware installation and software setup, you need to learn more about the

221. Output Level Fader/Level Meter These faders are the output volume control faders that controls 10 outputs of the Audioterminal 010. 10 outputs

23d. Level Meter The Level meter displays the signal level of the wave signal. You can see the level of each output to compare them and adjust the le

242. Input Level Fader Input Level Fader’s functions are same as Output Level fader. See the ‘output level fader’ part for reference. 3. Master Mix

254. Pull Down Menu The Audioterminal 010 control panel includes a pull down menu bar that contains the configuration for the Control P

26channel in this ‘Mapper’ menu. 8. Bus I/O In this menu, you can make specific setting of the Audioterminal 010. Select multi channel port such

27<SPDIF Mode> This will set 2 channel digital output format of the Audioterminal 010. - Consumer: (IEC 958 Type II) - Pro: (IEC 958 type I) &

286. Working with Applications 1. Cubase VST After launching Cubase, go to ‘Option’ -> ‘Audio setup’ -> System. Select ‘ASIO2.0-AT010’ for the

292. Sonar After launching Sonar, go to ‘Option’ -> ‘Audio’. Check ‘AT010 Stereo wave’ or ‘AT010 8channel wave’. Go to ‘Option’ -> ‘Audio’.

30Go to ‘Option’ -> ’MIDI Devices’. Choose ‘AT010 Midi’ for MIDI port. After set Latency you must click ‘Wave Profiler’ again. When you work in

4Features Audioterminal 010 supports ADAT format. You can use it with various digital mixer, digital recorder and hard disk recording

31

323. Nuendo Go to “Device” -> Device Setup” -> VST Multitrack Select ‘ASIO2.0 – AT010 for the ASIO Driver.

334. Wave Lab Go to ‘Option’ -> Preference -> Audiocard. Choose ‘AT010 Stereo wave’ or ‘AT010 8 channel wave’.  24bit play works only on W

34Specification 1ADAT Toslink I/O (8 channels) 1 TDIF/R-BUS I/O (25pin D-sub) Supports 16 and 24 bit resolution 32, 44.1, 48, 64, 88.2, 96 kHz s

5 Usually, a PCI card and a PC system exchange data via a 32-bit PCI bus. The Audioterminal 010 adapts PCI bus mastering that makes a low-CPU lo

62. Hardware Installation If you follow the instructions on this section in the sequence that it is written, you will have properly installed all com

71. The Audioterminal 010 PCI card is placed into the anti-static plastic pouch as it is packaged. Do not open the pouch before you in

83. Installing Audioterminal 010 PCI card 1. Please look for an empty PCI slot. IF you do not know which one is an actual PCI slot, Please read

9 3. Next, Put the Audioterminal 010 PCI card into the slot and make sure it is placed in the slot correctly. The card will fit into your slot and

103. Audioterminal 010 Software Installation After completing the installation of hardware for the Audioterminal 010, you need to install its driver