ESI ESP1010 Specifications

ESP1010 Second Edition Jan., 2005 Index 1. Introduction 2 2. What’s in the Box 2 3. Key Features 3 4

ESP1010 2. Installing ESP1010 PCI card 1) Look for an empty PCI slot. If you do not know which one is a PCI slot, please re

ESP1010 7. Software Installation After completing the hardware installation, you need to install the Windows driver. The ins

ESP1010 3. During installation, you will be prompted with a message warning that the driver software has not passed Windows L

ESP1010 6. If asked again, choose “Search for the best driver in these locations” and specify the location of the driver. Sel

ESP1010 9. After you complete both driver installations, you should restart your computer. 10. After restarting Windows, yo

ESP1010 12. Go to Control Panel → Sounds and Audio Device Properties → Audio tab. You can choose each stereo device or

ESP1010 8. ESP1010 Panel The ESP1010’s driver software provides a simple yet powerful interface with your computer. The pane

ESP1010 2. Config 1) Mouse Wheel: Configures the mouse wheel for volume change adjustment. Default value is ±1.5dB per step.

ESP1010 You can control gain from -60dB to +15dB (0.5dB per step) on input ch 1/2. Input 1/2 allows you enable +12V phanto

ESP1010 H·P: The signal from channel 1/2 can be sent to the headphone outputs. MIX OUT: Send out the mixer signal to output

ESP1010 1. Introduction Thank you for choosing the ESI ESP1010 – a unique PCI multimedia digital audio card with a full size

ESP1010 ESP1010. INT: Sets the ESP1010’s internal clock as the master clock. This is the recommended default setting. EXT: Wh

ESP1010 9. Configuring ESP1010 ESP1010 is a premium multimedia audio device for professional audio. It is simple to configur

ESP1010 Left Right Left Right Some applications like PowerDVD 5.0 supports 8 channel surround speaker outputs as shown below

ESP1010 2. Nuendo or Cubase SX / SL / SE After launching Nuendo or Cubase, go to Device → Device Setup → VST Multitrack. S

ESP1010 4. Sonar Sonar either supports ASIO (recommend, from Sonar 2.2 and newer) or WDM/KS. You can select the driver type

ESP1010 5. WaveLab 4.0 After launching WaveLab, go to Options → Preferences → Audio Card. Choose one of “MME-WDM 1-1010 “1/2c

ESP1010 2. DirectWIRE Panel Click on DirectWIRE on the ESP1010 panel. The DirectWIRE panel window as shown below will appear

ESP1010 3. DirectWIRE Examples NOTE: Please setup DirectWIRE before you start your audio applications. 1) Recording from W

ESP1010 4) Recording from GigaStudio(GSIF) to SONAR(WDM) 5) Recording from GigaStudio(GSIF) to Cubase(ASIO) 6) Let&ap

ESP1010 11. Specifications <Analog Audio> 1. Analog Inputs 1) Connector Type: 1/4" female TRS-type,

ESP1010 3. Key Features 1. Extremely High Quality ADC and DAC ESP1010 supports up to 96kHz sampling rate for digital record

ESP1010 1. Internal 20ch /36-bit Digtal Mixer(Input 10ch/Output 10ch) 2. Sample rate supports: (22.05,24)*,32,44.1,48,8

ESP1010 4. System Requirements ESP1010 is a multimedia digital audio device with many functions, not just a simple soundcard

ESP1010 5. Exterior Features 1. Rack - Front Part - 1) MIC. +48V ①(In1~2) –XLR MIC input 1 ~2 ports ②(+48V) – Phantom

ESP1010 NOTE: Input 1/2 can be used either via the XLR or 1/4” input connectors, however they cannot be used simultaneousl

ESP1010 4) D-SUB – Connect to 44pin D_SUB cable (Do not use any cable except the original cable by ESI). 5) External

ESP1010 1) D-Sub Connector – Connects ESP1010 PCI card with the Rack 2) Cable Connector – Connects with included MIDI I/O and

ESP1010 6. Hardware Installation ESP1010 requires multiple installation steps: · PCI card installation, rack connection · Dr